68kMLA Classic Interface
This is a version of the 68kMLA forums for viewing on your favorite old mac. Visitors on modern platforms may prefer the main site.
| Click here to select a new forum. | |
| Looking For Sonnet Presto PPC Disk Contents | |
| Posted by: macuserman on 2022-06-01 21:12:04 I'm looking for the original disk contents from the Sonnet Presto PPC, can't seem to find it online only the daystar power pro, I'd like to find the Sonnet files esp the Presto 8.5 Enabler. Files are referenced here in this manual: Any ideas? | |
| Posted by: jeremywork on 2022-06-01 21:24:28 I remember chasing this when I got my Sonnet Presto; it’s been a couple years now but at the time I couldn’t locate it. The PowerPro control panel has always worked perfectly, but I would also like to try the 8.5 enabler. I’ve attempted the ‘gusd’ modification in Resedit, which worked perfectly on a PowerBook 500 with 603e card, but I’ve had hangups trying to do the same with Q950s on 601s. | |
| Posted by: jeremywork on 2022-06-01 21:35:56 The OP on this other thread seems to have found a substitute in "Minimal 5300/2300/190 Enabler" from the 7.5.2 Disk Tools. I’ll have to try this later... need Sonnet Presto PPC Mac OS 8.5/8.6 Enabler softwareHi, I need Sonnet Presto PPC Mac OS 8.5/8.6 Enabler software. I don't have the card, it's for an investigation of how to make a system enabler myself.
68kmla.org
| |
| Posted by: jeremywork on 2022-06-01 21:44:22 The author of this site posted a link in the comments here. Hopefully it works! Quadra 950: MacOS 8.5 (and 8.6) « modelrail.otenko | |
Posted by: jeremywork on 2022-06-02 00:37:58The author of this site posted a link in the comments here. Hopefully it works!It works! Direct link here: http://www.otenko.com/macintosh/Presto-PPC-8.5.sit I'm not sure where I went wrong last time I tried the 'gusd' mod, because using the same System Folder again now works. Could be I was a goof and tried to boot without switching to 601 mode... Anyhow, I copied an existing 8.6 System Folder from my TAM and added "Presto PPC 8.5 Enabler" to the root directory, and the Quadra/601 happily booted to it. The "Presto PPC ID" extension changes the gestalt to 112 (7100/66) so the 8.5+ installers will run, same as Wish I Were or MachID Wannabe, and it's not needed to boot from the installed System. Thanks for bringing it up; I had given up searching before but I'm glad to have it now! | |
Posted by: macuserman on 2022-06-02 03:53:54It works! Direct link here: http://www.otenko.com/macintosh/Presto-PPC-8.5.sitWow! You were busy! I’m amazed you were able to find this I couldn’t find squat googling. Wonder if anyone would care if the files were uploaded to the garden or repository for easier finding in the future as well? That’s quite the find in a very large haystack! | |
Posted by: jeremywork on 2022-06-02 04:21:34Wow! You were busy! I’m amazed you were able to find this I couldn’t find squat googling. Wonder if anyone would care if the files were uploaded to the garden or repository for easier finding in the future as well? That’s quite the find in a very large haystack!I remember spending so much time chasing this the first time around I didn't really expect to find it, but I'm very glad it resurfaced! I must've been looking only a couple months before that comment was posted because I definitely remember reading that page. | |
Posted by: ArmorAlley on 2022-06-02 04:23:53Anyhow, I copied an existing 8.6 System Folder from my TAM and added "Presto PPC 8.5 Enabler" to the root directory, and the Quadra/601 happily booted to it. The "Presto PPC ID" extension changes the gestalt to 112 (7100/66) so the 8.5+ installers will run, same as Wish I Were or MachID Wannabe, and it's not needed to boot from the installed System.That's great news and thanks for the posting the file. How well does the Q950 run on Mac OS 8.6? | |
Posted by: jeremywork on 2022-06-02 04:45:50That's great news and thanks for the posting the file.Chugging was the first word that came to mind, but still very usable. This one's merely a 66MHz/1M model clocked at 77MHz, but even given the benefit of booting from a CF AztecMonster on a SiliconExpress IV it feels pretty slow. 8.1 feels snappy by contrast. I'm away from part of my stash at the moment, but now that I know this works I'd like to see how my other two compare. The 80MHz one with 64-bit memory should do much better I suspect, probably even better than the 100MHz/1M clocked at 115.5MHz can. The 950's non-interleaved 32-bit memory really drags compared to an 8100/100 or 840AV. | |
Posted by: macuserman on 2022-06-02 07:36:34I remember spending so much time chasing this the first time around I didn't really expect to find it, but I'm very glad it resurfaced! I must've been looking only a couple months before that comment was posted because I definitely remember reading that page.Well in any case thanks for doing the legwork on this, super helpful. I do think I'm going to put them on the repo or garden just for safety if nobody else beats me to it. | |
| Posted by: Phipli on 2024-03-27 10:44:13 While looking for where I uploaded it before I found this thread. In case someone else is looking : need Sonnet Presto PPC Mac OS 8.5/8.6 Enabler softwareAnd I shouldn't have called you a git, sorry :) What's the plan with your enabler? Is OS 8.5 usable on a PPC PB500? I've a Newertech 167Mhz PB540c that seems quite happy with OS 8.1; it has the original Apple SCSI to IDE adapter sled in it. Put a 16GB CF card and it's been fine, filled up...
68kmla.org
I also uploaded it here : Sonnet Processor Upgrade Drivers - Macintosh Garden1. Sonnet Driver.sit: Sonnet CPU Upgrade Extension Version 2.0 2002 The following info is taken from this 2005 page on www.archive.org https://web.archive.org/web/20050721001642/http://sonnettech.com/downloa... (Posted: June 17, 2005) 2. Crescendo/Encore™ Software: ce_install_v231.hqx Sonnet...
and specifically http://macintoshgarden.org/sites/macintoshgarden.org/files/apps/Presto_PPC_8.5.hqx | |
| 1 |